High End Network Analyzers
ZVA Vector Network Analyzers
ZVT Vector Network Analyzers
ZVA-Z Millimeter-Wave Converters

- Frequency range: 300 kHz to 8 GHz (R&S®ZVA8), 10 MHz to 24/40/50/67/110 GHz (R&S®ZVA24/40/50/67/110)
- Linear and nonlinear amplifier and mixer measurements
- Noise figure measurements
- Pulse profile measurements with 12.5 ns resolution
- True differential measurements for reliable characterization of active devices with balanced ports
- High output power typ. > 18 dBm
- Wide dynamic range typ. > 140 dB
- High measurement speed < 3.5 μs per test point
- Wide IF bandwidth: 1/5/30 MHz
- Versatile calibration techniques: TOSM, TRL/LRL, TOM, TRM, TNA, UOSM
- Automatic calibration units
- Phase and group delay measurements on mixers with and without LO access

- Frequency ranges from 300 kHz to 20 GHz, with two up to eight test ports
- Multiport measurements, avoiding any time loss due to matrix control
- Flexible configuration of test ports for balanced and single-ended measurements
- True differential measurements and coherent signal generation
- Enhanced performance by parallel measurements on several DUTs
- Multichannel receiver with simultaneous sampling of channels, e.g. for phase measurements on antenna arrays
- Automatic calibration units
- Point-in-pulse and pulse profile measurements with up to 16 receivers
- Up to 3 (R&S®ZVT20) or 4 (R&S®ZVT8) internal sources for flexible and efficient measurements on active devices, such as (double) converting transmitters, receivers etc

- Network analysis up to 500 GHz
- Variable output power
- Electronic power control
- Automatic parameter setting
- Convenient handling
- Multiport and true differential measurements
- Pulsed measurements
- Calibration
- R&S®ZVA-Z325 and R&S®ZVA-Z500 special compact version
- R&S®ZVA-Z110E: Electronic power control for power calibration, and calibrated power sweeps
ZCxxx Millimeter-Wave Converters
ZVAX24 Extension Unit
ZVAX-TRM Extension Unit

- Wide frequency range
- 110 GHz to 170 Ghz (R&S®ZC170)
- 140 GHz to 220 GHz (R&S®ZC220)
- 220 GHz to 330 GHz (R&S®ZC330)
- 325 GHz to 500 GHz (R&S ZC500)
- For use with an R&S®ZVA24, R&S®ZVA40, R&S®ZVA50, R&S®ZVA67 or R&S®ZVT20 network analyzer
- Wide dynamic range
- > 90dB, typ. 105dB (R&S®ZC170)
- > 100 dB, typ. 110 dB (R&S®ZC220)
- > 100 dB, typ. 115 dB (R&S®ZC330)
- > 85dB, typ. 100dB (R&S ZC500)
- Variable output power
- Automatic parameter setting
- Easy handling
- Highly stable measurements

- 10 MHz to 24 GHz
- The R&S®ZVAX24 extension unit for the R&S®ZVA simplifies advanced measurements on active devices such as amplifiers.
- Depending on the measurement tasks, it can be configured with combiners, harmonic filters, pulse modulators or high-power couplers.
- It is directly controlled by the R&S®ZVA via a graphical user interface.
- The combination of an R&S®ZVA and the R&S®ZVAX24 behaves like a fully integrated single box.
- However, if multiple R&S®ZVAs are being used in a lab, they can share the extension unit.
- This leads to an optimum utilization of investment

- Extension unit for an R&S®ZVA/ZVT network analyzer for measurements on T/R modules, receivers, transceivers and power amplifiers
- Base unit supports power levels up to +43 dBm
- Options for pulse modulation, amplification, high-power, noise figure and inter modulation measurements
- R&S®ZVAX TRM models up to 24/40/50/67 GHz
- Flexible configuration for the required application
- Straightforward dialogs for measurement configuration
- Automatic detection and control of R&S®ZVAX TRM via USB interface
Midrange Network Analyzers
ZNBT Vector Network Analyzer
ZNB Vector Network Analyzer
ZNC Vector Network Analyzer

- Four-port R&S®ZNBT8 base unit (upgradeable to 8, 12, 16, 20 or 24 ports)
- Eight-port R&S®ZNBT20 base unit (upgradeable to 12, 16, 20 or 24 ports)
- Frequency range from 9 kHz to 8.5 GHz (R&S®ZNBT8) or from 100 kHz to 20 GHz (R&S®ZNBT20)
- Up to 24 fully phase coherent receivers
- Wide dynamic range of up to 140 dB
- Short sweep times, e.g. 2.1 ms (R&S®ZNBT8) and 2.5 ms (R&S®ZNBT20) for a sweep across 201 points
- Wide power sweep range of 100 dB
- High power handling capacity
- IF bandwidths from 1 Hz to 10 MHz
- High temperature stability of 0.01 dB/°K
- More than 100 traces and channels
- Simple configuration of multiport measurements
- Manual and automatic calibration methods optimized for multiport applications
- Status information
- Compatible with all vector network analyzers from the R&S®ZVA/R&S®ZVT and R&S®ZNx families

- Frequency range from 9 kHz up to 40 GHz
- Wide dynamic range of up to 140 dB
- Short sweep times, e.g. 4 ms for 401 points
- High temperature stability of typ. 0.01 dB/°C
- Wide power sweep range of 98 dB
- Wide range of IF bandwidths from 1 Hz to 10 MHz
- Manual and automatic calibration/li>
- Large, high-resolution 12.1″ screen
- Touchscreen user interface
- Two or four ports
- Four-port model with two independant generators
- Expansion to up to 48 ports using switch matrices

- Frequency range from 9 kHz to 3 GHz
- Dynamic range of up to 130 dB
- Short sweep times of 11 ms for 401 points
- High temperature stability of typ. 0.01 dB/°C
- Wide power sweep range from –50 dBm to +13 dBm (typ.)
- IF bandwidths from 1 Hz to 300 kHz
- Manual and automatic calibration
- Low trace noise of 0.004 dB RMS at 10 kHz IF bandwidth
- Large, high-resolution 12.1″ screen
- Touchscreen user interface
Switch Matrix
Network Analyzer Accessories

- Full crossbar measurements up to 48 ports
- Easy setup with the R&S®ZNB
- Ready to use, no need to configure matrix hardware externally
- Supports use of automated calibration units
- Damage level: + 23 dBm,
- Remote control : LAN, USB, Direct Connect (only R&S®ZN-Z84 and R&S®ZN-Z85)

- Configuration of tests with vector network analyzers in production systems
- One software package to manage and control multiple test setups
- Optimization of production system speed
- Integration of external components (power supplies, multimeters, etc.) in test sequences by using plug-ins
- Control of DUT, e.g. via RFFE GPIO interface
- Efficient system error correction on test system
- Test setups centered around the DUT
Economy and Handheld Network Analyzer
ZNL Vector
ZNLE Vector
ZND Vector

- Frequency range from 5 kHz to 3 GHz (R&S®ZNL3) or 5 kHz to 6 GHz (R&S®ZNL6)
- Two-port vector network analyzer for bidirectional measurements
- Universal instrument concept
- Vector network analyzer
- Fully integrated spectrum analyzer option (for R&S®ZNL3)
- Display of power meter measurements
- Wide dynamic range of typ. 130 dB
- Output power range from –40 dBm to typ. + 3 dBm
- Measurement bandwidths from 1 Hz to 500 kHz
- Fast measurements, i.e. 16.7 ms for 401 points (100 kHz IFBW, 200 MHz Span, 2-port TOSM (SOLT))
- Compact size and low weight (6 kg to 8 kg)
- Optional battery pack available
- Windows 10® operating system

- Frequency range from 1 MHz to 3 GHz or 1 MHz to 6 GHz
- Two-port vector network analyzer with a full S-parameter test set for bidirectional measurements on passive components
- Wide dynamic range of up to 120 dB (typ.)
- Measurement bandwidths from 1 Hz to 500 kHz
- Fast measurements, i.e. 8.7 ms for 401 points (100 kHz IFBW, 200 MHz span, corr. off)
- Compact size (depth 24 cm) and low weight (6 kg)
- Standalone instrument with 10.1″ WXGA touchscreen
- Windows 10 operating system

- Two-port network analyzer for unidirectional measurements from 100 kHz to 4.5 GHz
- Frequency range can be extended to 8.5 GHz
- Test set can be enhanced for bidirectional measurements
- Touchscreen operation
- Dynamic range up to 120 dB
- Power sweep range up to 48 dB
- Bandwidths from 1 Hz to 300 kHz
- More than 100 traces and channels
- Compatible with all Rohde & Schwarz network analyzers
- Fast measurements, i.e. 16.7 ms for 401 points (100 kHz IFBW, 200 MHz Span, 2-port TOSM (SOLT))
- Compact size and low weight (6 kg to 8 kg)
ZVL Vector
ZVH Cable and Antenna Analyzer
Cable Rider ZPH Cable & Antenna Analyzer

- Frequency range: 9 kHz to 3 GHz/6 GHz/13.6 GHz. 75 Ω version: 9 kHz to 3 GHz. Portable network analyzers with optional spectrum analyzer in one unit
- Optional spectrum analysis and digital communications standards
- Bidirectional test set for displaying all four S-parameters
- R&S®ZVL3-75: 75 Ω vector network analyzer for TV and CATV measurements
- Multitrace display for displaying all relevant parameters
- Distance-to-fault measurement for detecting cable faults
- Time domain analysis
- USB connector for R&S®NRP-Z power sensor series for precise power measurements
- Internal battery and 12 V DC operation
- Small, compact, lightweight and portable

- Frequency range from 100 kHz to 3.6 GHz or 8 GHz
- 100 dB (typ.) dynamic range for filter and antenna isolation measurements
- Factory calibration over entire frequency range
- Built-in DC voltage supply (bias) for active components such as amplifiers
- Power meter option
- Saving of measurement results on SD memory card or USB memory stick
- Easy operation with user-configurable test sequences (wizard)
- Easy-to-replace Lithium-ion battery for up to 4.5 h of operation
- Rugged, splash-proof housing for rough work in the field
- Easy handling due to low weight (3 kg with battery) and easy-to-reach function keys

- Frequency range from 2 MHz to 3 GHz/4 GHz, upgrade via keycode
- DTF, return loss, VSWR and one-port cable loss measurements
- Ideal for field use: 9-hour battery life, 2.5 kg (5.5 lb), backlit keypad, fast boot time, non-reflective display, small form factor, ruggedized housing (IP51)
- Large color touchscreen
- Measurement wizard to speed up measurements and eliminate human errors
- Easy and cost-efficient upgrades of all options via software keycode
OUR CLIENTS


















































