R F & Microwave Accessories

Attenuator
N-Type High Power Attenuators, DC-18 GHz, 2~500 Watts
SMA Type High Power Attenuators, DC-18 GHz, 2~50 Watts
Variable Step Attenuators, DC-18 GHz, 0 ~ 101 dB Range
    Specifications:
  • Impedence : 50 Ohms
  • DC-18 GHz, upto 500W average power
  • Operating Temperature: -55 ~ 125 degree C
  • Average Power at 25°C ambient temperature
  • S21 plots available with shipment
  • Refer to detailed datasheets for peak power, VSWR performance data
    Specifications:
  • Impedence : 50 Ohms
  • DC-18 GHz, upto 50W average power
  • Operating Temperature: -55 ~ 125 degree C
  • Average Power at 25°C ambient temperature
  • S21 plots available with shipment
  • Refer to detailed datasheets for peak power, VSWR performance data
    Specifications:
  • Impedence : 50 Ohms
  • Broadband – Available in a choice of frequency ranges DC-18 GHz.
  • Wide Choice of Attenuation Ranges : 0 ~ 101 dB
  • Operating Temperature: -55 ~ 125 degree C
  • S21 plots available with shipment. Refer to detailed datasheets for VSWR performance data
  • Environmental – Conform to meet most environmental requirements of MIL-A-24215
  • Excellent Repeatability
R F Mixer
    Features
  • Mixers use high-performance monolithic diodes for superior isolation and the lowest loss possible.
  • Synthesized input and output matching networks maintain maximum response flatness across the performance band.
  • Quarter wavelength stubs are used to provide diode ground paths and optimize Return Loss.
    Specifications:
  • Mixers use high-performance monolithic diodes for superior isolation and the lowest loss possible.
  • Synthesized input and output matching networks maintain maximum response flatness across the performance band.
  • Quarter wavelength stubs are used to provide diode ground paths and optimize Return Loss.
R F Dividers
    Features:
  • Brand new and high quality.
  • Low insertion loss and high isolation.
  • Advanced manufacture technique and surface plating.
  • Frequency: 1500MHz – 8000Mz.
  • Split: 2-way.
  • Power: 50W max.
  • Insertion Loss:≤0.5dB max.
  • Amplitude balance: ±0.2dB Max.
  • Phase Balance:±3 Max. VSWR: 1 :1.3
  • Temperature range: -40 to – 70.
  • Connector type: SMA, 50 Ohms.
  • Size: 5.1cm x 3.4cm x 1.3cm
Aluminum case with removable lid. Installed stripline circuit board easily removed with 3 screws. Inside milled out to 1-1/4″ x 1-3/8″ x 5/16″. Outer dimensions: 2″ x 2″ x 3/4″. Power splitter / combiner is made for 800 – 900 MHz range
    Features:
  • Ideal for antenna, CATV and satellite TV coaxial operations
  • Can be used as a RF coax splitter for splitting signal from a RF coax source into multiple ones.
  • Used as RF coax combiner for joining multiple RF coax signals into one run.
  • Accurately split or combine your cable TV and antenna signals.
  • Distribute one RF coax line for 8 TVs or receiving devices.
  • Merge 8 RF coax lines into one for further distribution.
  • High isolation, perfect performance index.
  • The CATV Signal Splitter converts one standard RF coaxial cable .
  • RF shielded die cast housing for absolute minimal insertion losses.
  • Light weight and compact size.
    Specifications:
  • All ports F-(f)connector,75Ohm
  • Screening factor: 5-2400MHz≥100dB
Loads
Hi Power N Loads
Hi Power SMA Loads
2.92 Precision Terminations
  • Impedence : 50 Ohms
    DC-18 GHz, upto 500W average power
    Operating Temperature: -55 ~ 125 degree C
    Average Power at 25°C ambient temperature
    S21 plots available with shipment
    Refer to detailed datasheets for peak power, VSWR performance data
  • Impedance : 50 Ohms
    DC-18 GHz, upto 50W average power
    Operating Temperature: -55 ~ 125 degree C
    Average Power at 25°C ambient temperature
    S21 plots available with shipment
    Refer to detailed datasheets for peak power, VSWR performance data
  • Impedence : 50 Ohms
    DC-40 GHz, upto 20W average power
    Operating Temperature: -55 ~ 125 degree C
    Average Power at 25°C ambient temperature
    Refer to detailed datasheets for peak power, VSWR performance data
Cable Assemblies
Low Loss Pre-Connectorized Cable Sets, LL 58 Series
LL40 Series Pre-Connectorized Cable Sets
Sensor cable sets
  • LL58 series cable sets are designed as superior alternative to RG58, RG223 types. Usable upto 6 GHz with a wide choice of connectors like SMA, N, BNC, TNC and in various styles like straight, right angle and panel mounts.
  • RF Shielding is 90 dB. This is 30dB higher than 60dB (typical) for single shielded RG types.
  • Low Loss: Loss is 30% less than comparable size RG cables.
  • Flexibility: LL58 types are highly flexible and can be routed easily. They have the tightest bend radius available for any cable of similar size and performance.
  • LL40 series cable sets are designed as superior alternative to corrugated cables and RG214 cables. Usable upto 6 GHz:
  • Equivalent to RFS LCF14-50 and Andrews LDF1-50
  • Ideal replacement for corrugated types for advantage of FLEXIBILITY
  • Lower Loss alternative to “RG214” types with the same mechanical size
  • Low noise, high impedance cables with conductive coated dielectric for charge mode sensors. Reduce ‘tribo-electric’ effect induced output variations
  • Choice of Microdot 10-32, BNC, TNC connectors from world-class suppliers like Tyco, Rosenberger or equivalent.
  • MIL-39012 conformant
  • Drop-in equivalents to common Kistler, PCB, Dytran types readily available
  • Imported cables, MIL-C-17 conformant




OUR CLIENTS